🛠️ What Have You Done To Your LC250 Today?

I successfully installed my skid plates today thanks to the advice on this thread! Thanks everyone!
IMG_9171.jpeg
 
PPF the door sills, and finally took off the imax force badge. Having a blast with this buggy!
 
Just installed the illuminated (front) door sills. No tools, at night, in the dark, with a phone as a flashlight. The plug covering the OEM harness was the hardest part. Didn’t use the zip ties, really no need to.
I still have to figure out keeping the interior lights on for a bit after locking…I know the “door” button in the overhead console is there, but more setting I need to mess with…
I am embarking on the install. It looks there is a plug cover over the harness. I can’t tell how to remove that. I am afraid to break it? Please advise…
 
@DKing I just read another thread that said the plug cover is easily removed by squeezing the cover with needle nose pliers so that the tiny catch releases and the cover slides right off.
 
Ditched the large plastic hitch cover in favor of the smaller included piece. Added Land Cruiser hitch plug from ZR Tactical (look for him on ‘Mud in the 200 section) with an extended length locking pin.
I'm still looking for my plastic half cover. Dealer not any help. Where was yours stored? Was it in one of the storage pockets?
 
Does that stick to the windshield?
The adapter has double stick tape on it. Technically you could leave it up in the headliner, but I chose to stick it to the windshield in case I decide to change to a different dashcam later.
 
Didn’t do anything BUT got the confirmation that my GREENLANE sliders have been shipped out!
 
Last edited:
Nashfabco finished the ditch light brackets and rear half ladder. It retains use of rear glass which is awesome! Roof Rack is cut and should be powder coated Friday if final assembly goes well. Rear Molle Panels will be finished this weekend, I should have the build back on Monday or Tuesday and will update y'all then.
 

Attachments

  • IMG_6189.jpg
    IMG_6189.jpg
    642.1 KB · Views: 160
  • tempImagekJGVqA.png
    tempImagekJGVqA.png
    2.2 MB · Views: 150
  • IMG_6191.jpg
    IMG_6191.jpg
    608.9 KB · Views: 155
  • tempImagedgEtft.png
    tempImagedgEtft.png
    2.3 MB · Views: 165
  • tempImage74Vqk0.png
    tempImage74Vqk0.png
    2.1 MB · Views: 200
Last edited:
Finally installed the Wescott molle panel and roto mounts. I only ordered the driver side to see if I like it ans hkw much it impaired my view. Without any Rotos cans mounted you can see through their slats so the blind spot is not bad.

Wescott is having a Black Friday sale so I'll get the passenger side then to fit my Roto water cans for camping trips.
 

Attachments

  • Screenshot_20241019_184657_Gallery.jpg
    Screenshot_20241019_184657_Gallery.jpg
    1.3 MB · Views: 137
  • Screenshot_20241019_184628_Gallery.jpg
    Screenshot_20241019_184628_Gallery.jpg
    1.1 MB · Views: 126
  • Screenshot_20241019_183620_Gallery.jpg
    Screenshot_20241019_183620_Gallery.jpg
    774.2 KB · Views: 109
Awesome. Those look great.

There is another thread about exploring the idea of swapping in a bigger 21 gallon gas tank from the GX 550 or other after market options. How would you compare the pros/cons with the side panels and Rotos against a approx $3k theoretical main tank replacement?
 
Nice. Did you look at any with a courtesy double beep-beep in addition to the normal warning honk?
Lol, after I got done I hit the horn for a test my wife said you went from excuse me please to MOVE!
 
Back
Top